Z-Wave Q&A

Question 1

Which bypass do you recommend & stock, for use with lighting loads below 4 watts? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 2

Has anybody seen an issue where the Q outputs don't follow the S inputs? I have to toggle the state of the input switch a few times to get it to sync up. The input switch is the microswitch on my Heating Control Valve. View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 3

I am using a pir to switch this on which seems to work but it keeps showing as device not detected! I'm using Vera edge is there a parameter I need to change or is it not compatible thanks View answers

Asked 7 ´years ago | Z-Wave Fibaro Single Switch 2

Question 4

When will Aeotec Wallmote double be available for UK installation & quad back in stock? View answers

Asked 7 ´years ago | Z-Wave Plus Aeotec WallMote Quad

Question 5

Does this have the possibility of manual override in case Z-wave is down? I don´t see a button View answer

Asked 7 ´years ago | Qubino 32A Contactor for Smart Meter

Question 6

It says "For use with Qubino Smart Energy Meter". Is the Smart Meter a requirement to use this contactor or can it be used without it? View answers

Asked 7 ´years ago | Qubino 32A Contactor for Smart Meter

Question 7

Can this be controlled locally via SmartThings if there is no internet connection? It is possible to link a Z-Wave remote to it directly? View answers

Asked 7 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 8

Does this device work fully with HomeSeer? View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 9

Would there be a minimum GU10 number of lights that would not need a Fibaro dimmer 2 ? I have a number of circuits with GU10 lights 6W X 9 in a kitchen and out in a hallway 2 way circuits of 2 each by 2 and a circuit of 4. Would I need a dimmer bypass then for all circuits. View answer

Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 10

Does anyone know if this unit is stable with HomeSeer? I have a couple of the Fibaro Dual Relay units but their status reporting is flaky at best and I cannot rely on them. - Thanks! View answer

Asked 7 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 11

Hi - when wired this into a double switch and then included this with a Vera Plus controller there were 3 devices created - the master and 2x appliance modules. In Vera only using the master switch has an affect and it only controls one of the switches. How do I include this so that both switches are controlled? View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 12

The blurb on this product says you can connect an external probe, but one is not supplied. The picture shows a very neat looking probe. Can anyone recommend a specific (and cost effective) probe that is known to work with this sensor? View answer

Asked 7 ´years ago | Z-Wave Fibaro Flood Sensor

Question 13

Can this unit be controlled by other Z-wave controllers? Is the Smart Meter required for it to function?

Asked 7 ´years ago | Qubino 32A Contactor for Smart Meter

Question 14

Does this work with 3 way switched circuits? Can't find a wiring diagram for even 2way switching in the manual. View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 15

Out of stock within 3 days of email saying in stock. Pointless. Bad. How to lose customers.

Asked 7 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 16

How can this be set up for two-way circuits? i.e. two switches controlling one light. I can't see a wiring diagram to support this in the manual. View answers

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 17

My door is 76mm wide, do you have an extension kit for this lock? View answer

Asked 7 ´years ago | Yale Conexis L1 Smart Door Lock - Polished Chrome

Question 18

is this a straight swap for the existing Yale Smart living Keyfree multipoint lock? View answer

Asked 7 ´years ago | Yale Conexis L1 Smart Door Lock - Polished Chrome

Question 19

Does this have an outdoor IP rating? If so please could you let me know what it is?

Asked 7 ´years ago | Z-WAVE POPP Elektroninen ovi avaaja ControlModule kanssa Oven avaaja

Question 20

Does anyone know if there is a zwave module for this lock? View answers

Asked 7 ´years ago | Yale Conexis L1 Smart Door Lock - Polished Chrome

Question 21

For Vera is changing the device type to scene controller a guaranteed way to get the single button press to work every time? View answers

Asked 8 ´years ago | Z-Wave Fibaro Button

Question 22

Does Z-Wave Aeon Labs Clamp Power Meter Gen5 - One Clamp (60A) sense current direction, ie import or export of power? View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 23

Is this compatible with Home Assistant?

Asked 8 ´years ago | Z-Wave Fibaro Button

Question 24

does it detect carbon monoxide? View answers

Asked 8 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 25

Will this sensor work with an Aeotec Z-Stick V2 (Version: 1.4-2228-gbce4a88-dirty)?

Asked 8 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 26

If I had a chandelier with 5 X 6W LEDs (30W total) would I need a Fibaro Dimmer Bypass 2? View answers

Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 27

QNAP, OpenHAB + Aeon Labs Z-Stick USB, possible? I'm guessing this is possible, there is a package for OpenHab that will install on QNAP, so if I stick this USB stick into the back of the QNAP box will I be good to go? View answer

Asked 8 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 28

Is it suitable for outdoor? Looking to put it in a side gate so will be exposed to the elements. View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec Recessed Door Sensor

Question 29

I want to use a Fibaro relay to swicth an immersion heater on and off. The load is switched using a double pole relay. Can I simply connect the Fibaro output across the relay energising contacts, or will you need a resistor in series to reduce the current? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 30

Can someone explain dry / volrage free contacts? Trying to decide which module to use for controlling some outside lights. View answers

Asked 8 ´years ago | Z-Wave Qubino Flush 1D Relay Plus

Question 31

I'm unsure if they bypass is working/broken. Does it add extra wattage to the circuit? View answer

Asked 8 ´years ago | Z-Wave Fibaro Dimmer Bypass 2

Question 32

Does this module need retractive switches too? I'm guessing yes and it needs 2. View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 33

Is this device suitable for switching 230V LED lights, or would it be better to use the double relay switch instead? Since it doesn't have dry contacts, I'm wondering if the LEDs may flicker while switched off (as is the case for the dimmer module). View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 34

Will this work outside as a motion detection? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 35

Does this work with Vera Lite, using firmware 1.7.855? I'm currently using a LightwaveRF Mood Lighting unit to control my kitchen Sonos but this has more buttons, so would obviously allow me more options. View answers

Asked 8 ´years ago | Z-Wave Remotec Scene Master

Question 36

I look at the instruction manual for the wiring diagrams. I have two wires coming from the wall and it has no wall switch. When I moved in, it had a cheap strip light with shaver socket and its own onboard switch. I have removed this old fitting. I am planning to install an LED strip light running off 12V. I wish to use the Fibaro Dimmer 2 with bypass 2. When I look at the wiring diagram for a 2 wire setup, it assumes I will have a Wall Switch. This makes the diagram useless to me. Can anybody help with an adjusted diagram please? View answer

Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 37

Has anyone figured out how to set the light and humidity thresholds? The manual gives parameter values, sizes and hex/decimal descriptions but setting them don't match and the default values don't match the ones in the manuals, they aren't even close. Trying to set values gives me "Failed to set user settings" in my Vera Edge. View answers

Asked 8 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 38

Can you fit this in the light fitting or does it have to be in the switch socket? I think it probably has to be in the switch but I want to be sure before I start drilling out space behind the switch box. Thanks! View answers

Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 39

Which would work better with the Fibaro Dimmer 2? GU5.3 (MR16/12V) LED bulbs or GU10 (240V) LED bulbs? (I'm replacing MR16 halogen bulbs and trying to decide whether to convert to GU10 fittings). View answers

Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 40

Will it work wit fibaro HC Lite? View answer

Asked 8 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 41

What is the range at which the gestures will work over? And are there any materials the Swipe will not work behind, e.g. glass?

Asked 8 ´years ago | Z-Wave Fibaro Swipe

Question 42

The Fibaro Double Switch 2 Gen5 will work with vera plus? View answers

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 43

As far as I know this model like previous models should have "Manager Power" option, but in your site usage it didn't mention it. it realy does not have this option?! View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 44

Does this stick battery prevent it from forgetting the network routing? I bought the UZB and whenever i unplug it from the pc or just reboot the pc, all routing is reset and it starts all over again resulting many times in dead nodes.. Is this the correct behaviour? Dow the Aeon stick do the same? View answers

Asked 8 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 45

briefly switches on then off when I use the attached physical switch rocker. Have cabled as per diagram for a single switch S1 to switch COM leftmost live to switch Live mains live (old style red) to rightmost live mains neutral (old style black) to N bridged N and Q1. Device is picked up in smartthings though toggle on/off doesn't do anything ... only a brief switch on and off when using attached physical switch rocker. Any ideas? View answers

Asked 8 ´years ago | Z-Wave Fibaro Single Switch 2

Question 46

How many LED GU10 Spotlights can one use with ONE Fibaro Dimmer 2? And are there any recommended LED GU10 Spotlights? View answers

Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 47

How does this differ from the fibaro relay module? They seem to do exactly the same job. View answers

Asked 8 ´years ago | Z-Wave Fibaro Single Switch 2

Question 48

Does this support lower voltage DC like the earlier versions did, or only mains? View answer

Asked 8 ´years ago | Z-Wave Fibaro Double Switch 2

Question 49

Is this new Gen5 fuse protected to 8A To use in sockets or do you still require to fit an upstream fuse spur at 8A? Does this report power monitoring? View answer

Asked 8 ´years ago | Z-Wave Fibaro Single Switch 2

Question 50

In the manual it says 'Electrical installation must be protected by directly associated over current protection fuse 4A, gG or Time lag T....'. How can I do this? View answers

Asked 8 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Z-Wave Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools