Z-Wave Q&A

Question 1

Is it possible to use these to control a 240v relay without chatter? We tried this by altering parameters 11,12 and 15 but were not successful. Any advice appreciated. View answer

Asked 7 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 2

hello - wanted to ask if the device provides data per phase or as a total. thanks!

Asked 7 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - Three Clamps (60A)

Question 3

Hi all, I have installed a couple of these (fgs223) on a 2 way switch. One is an on off switch and the other is a dimmer. I've put the switches behind the on off switch. That bit works well but now the separate dimmer won't dim it only switches on and off. Any suggestions? View answers

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 4

Z-Wave Fibaro KeyFob working with the Vera plus ?

Asked 7 ´years ago | Z-Wave Fibaro KeyFob

Question 5

Does anyone know the trick to getting full functionality (press, press and hold, double press etc.) working with Domoticz?

Asked 7 ´years ago | Z-Wave Remotec Scene Master

Question 6

Is the common connection a 3v output like the micro modules?

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 7

When controlled by the local switch, can the level be controlled e.g. press briefly to turn on/off, press and hold to cycle the brightness? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 8

Is anybody using this with Vera Plus and 1.7.2935 and, if so, how many functions per button is it now supporting ? View answers

Asked 7 ´years ago | Z-Wave Remotec Scene Master

Question 9

I think I need this, since my LED lamp still glows a bit when it should be off, but am not clear on how it is meant to be fitted. The wiring diagram in the manual is hopeless - so do you have to put this inside the light fitting somehow ? I don't see where it would physically go, to bridge across the bulb. There are two lights driven by the same switch, so do I need to bypass them both ? View answers

Asked 7 ´years ago | Z-Wave Fibaro Dimmer Bypass 2

Question 10

Is this Controller working with vera plus? View answer

Asked 7 ´years ago | Z-Wave Qubino Flush Shutter Plus

Question 11

Is it possible to label the buttons on this unit? Previous controllers I have used in the past had clear plastic covers on the buttons that could be popped off and a slip of paper with the button's function slipped underneath. View answers

Asked 7 ´years ago | Z-Wave Remotec Scene Master

Question 12

hello does anyone know if there is a template for the fibaro hc2 so it will work properly. thanks

Asked 7 ´years ago | Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 13

What connectors do I need to order to extend this cable? I can get them from Farnell or RS if I know what are used. I'm assuming that this is a 1-wire sensor as it has three wires, pwr, gnd and the 1-wire bus, and that means that it can be extended to quite a few metres and I need to pick up the outside temperature... View answers

Asked 7 ´years ago | Qubino Temperature Sensor

Question 14

Can these be placed in an unfinished loft/attic? Some smoke detectors specifically state not to place them in an unfinished attic (e.g. Nest Protect) due to the large temp changes etc. Could not find anything specific re. these so thought I would pose the question here. Thanks chaps! View answers

Asked 7 ´years ago | Z-Wave Fibaro Smoke Sensor

Question 15

Does anyone know if you can control the LED colours from Vera Plus? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Smart Switch 6 - UK

Question 16

Does this item work with Fibaro HC2 please View answer

Asked 7 ´years ago | Z-Wave Popp Z-Rain

Question 17

Has this been proven to work with HomeSeer?

Asked 7 ´years ago | Z-Wave Fibaro Button

Question 18

How many 240V GU10 Led Bulbs (Dimmable ones) can the FD2 support? I have 3 light fittings for outside my house that house 2 GU10 240 Bulbs or GU10 240V Dimmable Bulbs. I am going to use the LED Dimmable bulbs which on the box say "Use only 7 watts per bulb". So a total of 6 bulbs in 3 light housings. I'm going to wire them back to a junction box in parellel (not serial) and into then into the FB2 but was worried that 6 bulbs of this type (or even 10) would fry it? I have the original Fibaro Bypass Module also (FGB001) which I bought a few years ago but never used, could I use this if I need it? The LED 240v GU10 bulbs are "dimmable" Thanks! Andy View answers

Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 19

Why do these show as requiring a fuse whereas other like the Fibaro do not show this as a requirement in the wiring diagrams? View answer

Asked 7 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 20

Do you think this product would be ok to control a cooker? View answers

Asked 7 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 21

Is this 2 wire compatible. i.e. Does it require a neutral? View answer

Asked 7 ´years ago | Z-Wave TKB Dual Paddle Wall Switch TZ36D - Gen5

Question 22

Can this be connected to two bell-push switches, to activate two lighting scenes? The lights would be powered by other zwave modules (dimmers), so these would purely be used to trigger the scenes. View answer

Asked 7 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus

Question 23

hi is this light dependent . ie only work at night ? also does it work with n-cube controller?

Asked 7 ´years ago | Z-Wave Philio Motion Sensor PSP05 - Gen5

Question 24

Hi, I had successfully setup 1x MultiSensor 6 (ZW100-C) which required a change of device type. I then purchased 2 more (same model, same firmware) but they have aren't detecting any motion. Is there any advice on how to resolve this? I have tried a number of different DTH, removing and repairing etc and now looking for some help.

Asked 7 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 25

Are there any special instructions for including this in a Vera Edge system. It seemed to install but will only notify about tampering and has no apparent reaction to movement other than a small fashing led. No notifications.

Asked 7 ´years ago | Z-Wave Philio Motion Sensor PSP05 - Gen5

Question 26

Does this work with Vera Edge ?

Asked 7 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 27

how do these perform with metal back boxes? Is there a significant reduction in effectiveness / range? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 28

Is it possible to change colors of the light bulb using smartthings View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 29

Does this need ventilation? I was planning on using these in the loft for the upstairs lighting and putting them in PVC boxes along with any connectors etc. This is to keep things neat and safe but wondered if I need to drill holes in the boxes for ventilation? View answers

Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 30

If I mount this in a roof, what's the max angle that it can be moved to in the horizontal & what's the andle of detection?

Asked 7 ´years ago | Z-Wave Philio Motion Sensor PSP05 with Round Recessor - Gen5

Question 31

How is the quality of the key chain? It looks very frail as seen from the picture. I just wonder how long time it would survive in my keys View answers

Asked 7 ´years ago | Z-Wave Fibaro KeyFob

Question 32

What is new from the previous version. Looks pretty the same View answer

Asked 7 ´years ago | Z-Wave Fibaro Universal Door & Window Sensor 2

Question 33

hello, does anyone know if this can be used with a fibaro hc2 and does it do anything else like lux, temp or humidity. thanks View answers

Asked 7 ´years ago | Z-Wave Philio Motion Sensor PSP05 - Gen5

Question 34

The uses states security gates, does this mean it's waterproof and suitable for outdoor use now? View answers

Asked 7 ´years ago | Z-Wave Fibaro Universal Door & Window Sensor 2

Question 35

Will it still accept an external temperature probe like the original model? View answer

Asked 7 ´years ago | Z-Wave Fibaro Universal Door & Window Sensor 2

Question 36

Hi. What wireless switch could I use with this dimmer? And do I need a 3rd party device (e.g. Vera or Smartthings) to configure them to talk to each other? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 37

Hi, will two of these fit in a two gang wall box? I have both pendant and wall lights in my lounge View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 38

Use for a UK 2-wire (No neutral) switch with a 13W LED non-dimmable bulb in hallway, do I need to install with the bypass 2? View answer

Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 39

Will this work with the latest Aeotec Nano Dimmer for which does not have a bypass available yet? I cannot beleive that the internals will be much difference between provisors - basically some additional resistance and capacitance added. Has anyone tied this and can report compatability? View answer

Asked 7 ´years ago | Z-Wave Fibaro Dimmer Bypass 2

Question 40

Will this work with a PWM Immersion heater (ie. one that can very it's power). Other meters give false readings for me when it's on.

Asked 7 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - Three Clamps (60A)

Question 41

Can you confirm that S2 can control a second lighting circuit alongside one on S1? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 42

In the US they sell a touch display that plugs directly into this module but its the wrong size for the UK. Does anyone know if they will sell a UK version? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 43

Can this module be used behind a standard UK Socket and control/monitor it? View answer

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 44

What does the physical switch attached to this device do? does it activate the dimming or does it just enable/disable the whole device? Forgive the naiivety of the question, I'm still a noob at this View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 45

Manual says it transmits every 15mins in Normal mode. But does the message contain multiple readings or only a single reading covering the entire 15mins. I am after history with lower granularity, say 1min, but don't want to drain battery with Real-Time mode.

Asked 7 ´years ago | Z-Wave Data Logger for E-Meters

Question 46

Will this work with the new smart gas meters. (EDF have installed a Flonidan branded Smart Gas Meter but it cannot connect to the mobile telephone network so cant get at the data)

Asked 7 ´years ago | Z-Wave Data Logger for E-Meters

Question 47

What's the difference between this model (FIBEFGS-223) and the FIBEFGS-222? One is described as a switch and the other as a relay, but otherwise seem identical. Does it make any difference to what it can do? I want to use them behind existing light switches to control lighting circuits - does it make any difference which I use? Thanks! View answers

Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2

Question 48

How is this better than the Fibaro Dimmer 2 (which I just bought)? "outperforms all that has come before it" is quite a grand claim - is it just compatible with a broader selection of LED bulbs? View answer

Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Dimmer

Question 49

Does this have Low Battery Alert? View answers

Asked 7 ´years ago | Z-Wave Fibaro Flood Sensor

Question 50

Does this work with Samsung SmartThings Hub? View answers

Asked 7 ´years ago | Z-Wave Fibaro Flood Sensor

Z-Wave Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools