Temperature Q&A

Question 1

Appropriate for fridge and freezer View answer

Asked 1 ´year ago | Z-Wave Plus Aeotec aërQ Temperature & Humidity Sensor

Question 2

Do these use the same motion sensor as Aeotec's Multisensor with motion, UV, humidity, vibration, temperature and lux? I'm hoping they don't as the motion sensor in the Aeotec 6-way multisensor is very poor, I have about 5-6 of them and even on the highest setting they often don't detect me even if I walk right up to them and jump around.

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 3

battery? View answer

Asked 9 ´months ago | Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 4

How do you open it? View answer

Asked 9 ´months ago | LS Control Z-Wave Temperature Sensor

Question 5

The humidity sensor doesn't seem to be returning any data, any ideas? View answer

Asked 9 ´months ago | LS Control Z-Wave Temperature Sensor

Question 6

what is the operating frequency View answer

Asked 9 ´months ago | Z-Wave Plus Aeotec MultiSensor 7

Question 7

Is it support EU frequency (868.42) and work with vera?? View answer

Asked 9 ´months ago | LS Control Z-Wave Temperature Sensor

Question 8

Is it true that Vesternet Z-Wave devices are -NOT- compatible with hubs / devices sold for use in the US / Canada? View answer

Asked 9 ´months ago | LS Control Z-Wave Temperature Sensor

Question 9

I have connected it to my hubitat, it shows up ok but does not show the temperature on my dashboard View answer

Asked 1 ´year ago | LS Control Z-Wave Temperature Sensor

Question 10

Is this compatible with hubitat hub, View answer

Asked 1 ´year ago | LS Control Z-Wave Temperature Sensor

Question 11

how to do a factory reset? View answer

Asked 1 ´year ago | LS Control Z-Wave Temperature Sensor

Question 12

No instructions View answer

Asked 1 ´year ago | LS Control Z-Wave Temperature Sensor

Question 13

What Z-wave frequencies does the model you are selling work on ?I'm after one that will work in Aus (919.8 MHz, 921.4 MHz) View answer

Asked 2 ´years ago | Z-Wave Plus Aeotec MultiSensor 7

Question 14

Sensor 6 has several flaws. Reset button link via a piece of dodgy plastic, poor light level reading, poor UV reading.Apart from these, it was very good. Have they been addressed in Sensor 7? E.G. What range is read for the light level?Can I trust the reset mechanism? Can I assume it will work well with RaZberry? View answer

Asked 3 ´years ago | Z-Wave Plus Aeotec MultiSensor 7

Question 15

Can't add this to Homeseer - just errors on Addnode.Also, previously with version 6 I have a poe splitter to power it.With this version it doesn't seem to work and a USB to micro usb is supplied. Presumably I need to poe split differently??? ( not entirely sure why it doesn't power ) View answer

Asked 2 ´years ago | Z-Wave Plus Aeotec MultiSensor 7

Question 16

Is the battery rechargeable or replaceable? View answers

Asked 5 ´years ago | Z-Wave Philio Multisensor - PIR / Light / Temp - Gen5

Question 17

When you add a Z-Wave network the sensor FGMS-001 (controller Razbery) in the settings is displayed only temperature and illumination. No tamper and motion sensor. Accordingly, they are not in applications. Removed from the network, he added, the problem is not resolved. What to do?

Asked 7 ´years ago | Z-Wave Fibaro Multi Sensor

Question 18

Seeing as this product it battery operated and always monitoring temperature, lux reading and motion detection, how long does a battery typically last on this? View answer

Asked 6 ´years ago | Z-Wave Fibaro Multi Sensor

Question 19

Philio 2 in 1 Temperature/Humidity Sensor. What is accuracy of measurements? What is battery life if polling every 30 minutes? View answer

Asked 4 ´years ago | Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 20

is this using 868.4Hz frequency? View answer

Asked 6 ´years ago | Z-Wave Fibaro Multi Sensor

Question 21

Is this Trisensor replacing the Aeotec Multisensor 6, which has 6 different sensors?

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 22

Is it support EU frequency (868.42)? View answer

Asked 3 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 23

I'm about to include this item in my system run by a Vera Edge. The inclusion routine on the Edge offers me the PAT02-C (flood sensor) and the PAT02-B (Temp/Humidity sensor) and a number of other Philio sensors but not the PAT02-A which is this item. Any suggestion what I should choose? I am reluctant to go with Generic Z-Wave device because experience has taught me this does not work well with multi element devices. View answer

Asked 4 ´years ago | Z-Wave Philio Multisensor - Flood / Temp / Humidity - Gen5

Question 24

How long is the sensor lead? and it be lengthened if needed? View answer

Asked 4 ´years ago | Z-Wave Philio Multisensor - Flood / Temp / Humidity - Gen5

Question 25

How easy is it to get these working with smartthings?

Asked 6 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 26

How close does the door open sensor need to be to the main unit? View answer

Asked 3 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 27

How can I configure this device for low water level detection? And how can I disable the optical and acoustical signal? View answer

Asked 6 ´years ago | Z-Wave Philio Multisensor - Flood / Temp / Humidity - Gen5

Question 28

Hi Folks. Is it feasible to use this sensor to control your central heating. If I used a fibaro relay to control the boiler could the temperature sensor be used as a thermostat to set or monitor the temperature or would I need to buy a dedicated Zwave thermostat? Any advice would be greatly appreciated. View answer

Asked 7 ´years ago | Z-Wave Fibaro Multi Sensor

Question 29

hello does anyone know if there is a template for the fibaro hc2 so it will work properly. thanks

Asked 7 ´years ago | Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 30

Has someone tested this device with a veraplus controller ? (Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5 PHI_PST02-1A)

Asked 8 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 31

Does this work with Vera Edge ?

Asked 7 ´years ago | Z-Wave Philio Multisensor - Door / PIR / Light / Temp - Gen5

Question 32

Does this work with cats? Pet Friendly? View answer

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 33

Can this product be used outdoors? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 34

Can the unit be run from a USB / mains power supply? I don't trust the battery life claims from manufacturers. View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 35

Can the earthquake mode be ran concurrently with motion detection? View answer

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 36

As this can be immersed in water for low water level detection, can it give the temperature of the water. I was thinking of using this in a fish tank for water temp readings. View answer

Asked 6 ´years ago | Z-Wave Philio Multisensor - Flood / Temp / Humidity - Gen5

Question 37

Whats new in this Gen 5 version? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 38

Is it resistant to condensation/waterproof? What is the operating humidity range? View answer

Asked 3 ´years ago | Z-Wave Fibaro Multi Sensor

Question 39

I bought this motion sensor and tried without success to include to my new smartthings hub v2 (UK version). Smartthings support advised me to confirm that the motion sensor is also a UK version (not a US one), as apparently the frequencies are different... Can you please confirm that this sensor works with the UK version of smartthings hub? View answers

Asked 6 ´years ago | Z-Wave Fibaro Multi Sensor

Question 40

I have one of these and a Samsung smart hub... hoping use various items from one place. The motion sensor is recognised as a door/window sensor? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 41

How is this powered please? Battery / mains? Thanks View answers

Asked 7 ´years ago | Z-Wave Philio Multisensor - Flood / Temp / Humidity - Gen5

Question 42

Does this new Z-Wave Fibaro Motion Sensor Gen5 version work with the zipabox? or is it just vera edge having problems? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 43

Will this work outside as a motion detection? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 44

Does this work with both UI5 and UI7? View answers

Asked 8 ´years ago | Z-Wave Fibaro Multi Sensor

Question 45

If powered by USB, can the batteries be left in to cover a power failure? View answer

Asked 2 ´years ago | Z-Wave Plus Aeotec MultiSensor 7

Question 46

Hellow, is this product will work in israel with existing modules? where the zwave frequancy is 916? View answer

Asked 2 ´years ago | Z-Wave Philio 2 in 1 Temperature / Humidity Sensor - Gen5

Question 47

How can I monitor the temperature of my house remotely? View answer

Asked 29 ´days ago | Temperature

Question 48

How do I know if my temperature sensor is accurate? View answer

Asked 29 ´days ago | Temperature

Question 49

Why is battery life important for temperature sensors? View answer

Asked 29 ´days ago | Temperature

Temperature Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools