I was seriously thinking about buying one of these for a house I am buying off plan but put off by the fact that this cannot be installed in direct sunlight and needs to be protected from rain. How can this be used as an external door entry system if it can’t be used outside? Also, with the camera, can I hook this up to an NVR to record the live stream like a CCTV camera? If the above can be confirmed, that would be great! Thanks, Hal View answer
Asked 7 ´years ago | Fibaro Intercom
I have a fused Switch controlling a fan and want to use this controller to operate the fan remotely as well as enabling the fused switch to continue controlling the fan at the wall, is there a wiring diagram showing how to achieve this? View answers
Asked 7 ´years ago | Z-Wave Plus Aeotec Nano Switch On/Off Controller
Does it disconnect the neutral line as well ? View answer
Asked 7 ´years ago | Z-Wave Plus Secure Wall Switch
This installed with 4 SES002 and paired to Vera Edge. Vera reports the correct ambient temp agains the first sensor but all 4 pipe sensors report "-327.68 °". Ive checked all the connections, removed and reattached from the Zwave network etc but stays same. What can you suggest pls View answers
Asked 7 ´years ago | Z-Wave Plus Secure SES302 Temperature Sensors Gen5
Hey, will it work with the Vera Plus?
Asked 7 ´years ago | Z-Wave Philio 2 * 1.5 KW Relay Inserts
Hi there, I'm looking for a Z-wave dry contact switch, connected to my existing pilot wires from the boiler. Not really fussed about it being a thermostat, as all I need is to be able to remotely turn the heating on or off. I don't want to have to change out anything with the existing boiler's timer / programmer. I intend to leave it heating turned on at the boiler indefinitely, and the dry contact switch as the main on-off. I can then use scenes to control timing if need be. I don't think this Secure product is built for that since it needs replacing the boiler's timer / programmer. Can you kindly recommend a suitable product? Thanks in advance. View answers
Asked 7 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
Can this be used with the 2 channel boiler receiver? If so, how does it manage the hot water channel? I have a Razberry but wanted this to manage in the case of its failure (and because I understand it will manage the boiler better?) View answers
Asked 7 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
Is this Controller working with vera plus? View answer
Asked 7 ´years ago | Z-Wave Qubino Flush Shutter Plus
What connectors do I need to order to extend this cable? I can get them from Farnell or RS if I know what are used. I'm assuming that this is a 1-wire sensor as it has three wires, pwr, gnd and the 1-wire bus, and that means that it can be extended to quite a few metres and I need to pick up the outside temperature... View answers
Asked 7 ´years ago | Qubino Temperature Sensor
I read the following in the manual: Rated output power 8A for single output channel,13A at max.(3,25A for R.G.B.W. single output channel is suggested) I'm planing to control two strips of LED with the RGBW-Dimmer. Using two of the four channels. How much power (current) can each of the two LED-strips have? (I'm using a 24V driver). Maybe 13A/2 = 6.5A per channel? View answer
Asked 7 ´years ago | Z-Wave Qubino RGBW Dimmer Plus
Asked 7 ´years ago | Z-Wave Plus Aeotec MultiSensor 6
Does this use the European or USA Z-wave frequency? View answer
Asked 8 ´years ago | Z-Wave Plus Secure Wall Switch
QNAP, OpenHAB + Aeon Labs Z-Stick USB, possible? I'm guessing this is possible, there is a package for OpenHab that will install on QNAP, so if I stick this USB stick into the back of the QNAP box will I be good to go? View answer
Asked 8 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)
Multiple questions --> What is the difference between the bi-stable and the contactor switch ? I need to switch a load of ~ 4k W (electrical water heater) which uses a double switch (live+neutral), which one suits better ? Do u have any feedback from Vera users that have managed to add them in their network (smart meter, contactor, bi-stable) ? View answer
Asked 8 ´years ago | Qubino 32A Bistable Switch for Smart Meter
Can this device with Fibaro Home Centre 2? View answers
Asked 8 ´years ago | Z-Wave Qubino Flush Shutter DC
I currently have have 1x SRT321 thermostat and 1x SSR303 actuator and ordered a bunch of LC-13 TRV's - however I would need to be able to trigger the boiler if the temperature drops in a room other than where the main SRT321 is located. If I understood the manuals correctly, I shouldn't send the trigger command from my Vera because the SSR303 will go into fail-safe mode if the trigger isn't re-sent within the next hour. So I guess ideally one (or more) SRT321 should be managing the SSR303? So my question is: can multiple SRT321 thermostats be paired with a single SSR303 actuator? View answer
Asked 8 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
