I have several of these devices and wish to use them with Home Assistant. I have managed to lose the little document that came with them. Can you tell me what values I should use to know when the sensor has detected smoke, please? Many thanks, John Chapman View answer
Asked 4 ´years ago | Z-Wave Plus Heiman Smoke Sensor
Will I be able to use the RaZberry 2 with it's Z-way software as a secondary controller on my Hubitat to analyse Z Wave Network and remove any ghost nodes and troubleshoot any routing issues. I know this is possible with Silicon labs PC controller and a UZB Stick but I do not own a PC. View answer
Asked 4 ´years ago | Z-Wave.me RaZberry 2 PI GPIO Daughter Card - Gen5 - New
Does this module work with the Hunter Douglas M25S 24V motor used in Luxaflex Duette blinds? https://motorisation.hde.nl/wired/24V/Motors/M25S/M25S-data-sheet/M25S-data-sheet.pdf On paper it all looks good but I know sometimes that doesn't work out in practice when motors have soft start/stop View answer
Asked 4 ´years ago | Z-Wave Qubino Flush Shutter DC
If I put the relay on momentary mode and press the momentary switch once (and release), the light that connect to relay output will stay at ON (toggle) till I press the momentry again, is that correct? If so, does it means that for 2 way implementation I just need 2 momentry switches connect in parallel to the same input at the qubino 2 relay and every press on one of the momentry switch will toggle the light to ON or OFF? I can't find such suggestion in you app notes guides. Thank you! View answer
Asked 4 ´years ago | Z-Wave Qubino Flush Relay x 2 Plus
Why does the Aeotec Multi 6 report a 23 lux when my Philips Hue sensor reports 14606 lux in virtually the same position. I've tried it with 3 Aeotec Multi 6s now with the same sort of difference, I'm concerned because I want to use to switch on lighting when required? They even report 0 lux when there is enough light to read a book! View answers
Asked 4 ´years ago | Z-Wave Plus Aeotec MultiSensor 6
will this work with fibaro dimmer 1 ? View answer
Asked 4 ´years ago | Z-Wave Plus Aeotec Nano Dimmer Bypass
I am thinking of buying a srt 321 to manage two electric radiators that have one zwave switch each. Is it possible to associate TWO nodeids in group 2 (on/off group) with the thermostat? Some forums say that you only can associate with one nodeid. Yes, I know that I can create scenes and automations in the controller, but I would like to do it locally as it is in the guesthouse and communication is not always reliable. View answer
Asked 5 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
At description it says: "and can also be operated by third-party controllers which support 'Thermostat Mode SET' commands or 'Binary Switch SET' commands." this is bit confusing, will it work with something like smart things hub or hubitat hub? for same idea, as one person already asked, like zoned heating with smart zwave trv's.? View answer
Asked 5 ´years ago | Z-Wave Plus Secure Boiler Receiver HRT Gen5
you said: Popp Mains Adapter can be used to power up the Z-Wave Popp Smoke Detector with mains supply. It eliminates the need to insert batteries in your smoke detector. after we tried to install it without battery it doesn't work then we contacted aeotec support they said: The smoke detector only works with the battery inserted. The smoke detector standard stipulates this. The 12 V supply serves to support the lifetime of the device by supplying the Z-Wave circuit board with external voltage. This doubles the lifetime of the 9V battery. could you explain please? Ahmad View answer
Asked 5 ´years ago | Z-Wave Popp Mains Adapter
What Bypass should be used in a 2-Wire installation? The manual says; "When installing the Mini Dimmer, with LED loads, in a 2-wired installation, if the load connected to the output starts flickering, we recommend you use a Bypass." I have installed it in to a 2-wire installation with an LED light and it is flickering. The Aeotech and Fibaro dimmers all say that only their own bypass modules are compatible, is this also the case with the Qubino dimmers? View answer
Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer
Hi does this support LED bulbs? View answer
Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer
Will this device work fully with Hc2? Thanks View answer
Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer
Which z wave stick / hub / device do you recommend for use with Secure Thermostat / Receiver and Homeseer? Please note I am a long time user of Homeseer (early 2000) upgrading from HS1,2 to HS3. For the last 15 years I have used a purpose designed multi (6) zone system controlled by Homeseer running Xap plugin to Phaedrus NETIOM to create heating scenes. I am now moving on to an existing single zone combi boiler dwelling. I have no desire or requirement to rejig the new system to a plumbed multi-zone effort. I see this combination as a first step to migrate to a zwave set up from my X10 devices, curing the heating issue in the process. View answer
Asked 5 ´years ago | Z-Wave Plus Secure Wall Thermostat & Receiver Set - Gen5
Why should i use this product? View answer
Asked 5 ´years ago | Z-Wave Plus Aeotec Nano Dimmer Bypass
Can this be mounted outside? View answer
Asked 5 ´years ago | Z-Wave Plus Aeotec MultiSensor 6
I currently have a single piece door handle and lock cover on a uPVC door. 1. It looks as though this device only covers the lock - is this assumption right? 2. Does it then need mounting to the door with screws? I'm just a little concerned about more holes in the door... Anyone actually fitted one? A few practical comments would be invaluable. Thanks View answer
Asked 6 ´years ago | Z-Wave and Bluetooth Poly-Control Danalock V3
Asked 6 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)
Asked 6 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
Why do you list this as compatible with Anthony Homey? Like many so called compatible brands, Homey relies on 3rd party or community developers to write drivers (they call them Apps), and the various developers haven't added compatibility for this or original Yale Connected Keyfree), despite requests. Now that the lock is discontinued, I doubt it ever will be. View answers
Asked 6 ´years ago | Yale Smart Living Z-Wave Module 2
Does this work with the Yale YMF 40 Mortise Lock?
Asked 6 ´years ago | Yale Smart Living Z-Wave Module 2
Asked 7 ´years ago | Yale Smart Living Z-Wave Module 2
Does this module work with Fibaro? View answers
Asked 7 ´years ago | Yale Smart Living Z-Wave Module 2
is this z-wave plus ?? View answer
Asked 7 ´years ago | Yale Smart Living Z-Wave Module 2
