Home Assistant Compatible Q&A

Question 1

Do you have the EU version? Z-Wave Fibaro Wall Plug Gen5 I need something The will work with Israeli plugs View answer

Asked 4 ´years ago | Z-Wave Fibaro Wall Plug - Schuko

Question 2

Hi , its z wave 868 hz (eu) ? View answer

Asked 4 ´years ago | Z-Wave Fibaro Walli Outlet - Schuko

Question 3

At description it says: "and can also be operated by third-party controllers which support 'Thermostat Mode SET' commands or 'Binary Switch SET' commands." this is bit confusing, will it work with something like smart things hub or hubitat hub? for same idea, as one person already asked, like zoned heating with smart zwave trv's.? View answer

Asked 4 ´years ago | Z-Wave Plus Secure Boiler Receiver HRT Gen5

Question 4

Is this work with Samsung Smartthing V3 hub? Can I use it to switch on and off the philips Hue smart light with Hue Bridge? View answer

Asked 4 ´years ago | Z-Wave Remotec Scene Master

Question 5

Hi, controlling through a z-wave hub (Fibaro HC2) can this turn on and off other IR controlled devices ie ceiling fans, lights TV etc? View answer

Asked 4 ´years ago | Z-Wave Remotec ZXT-600 Z-Wave+ to IR Extender for AC

Question 6

Hi does anyone know if this device is supported on the Fibaro Home Centre and if so what does the control panel look like? View answer

Asked 4 ´years ago | Z-Wave Qubino RGBW Dimmer Plus

Question 7

What do I kneed to by to be able for my Fibaro home center 2 to sense my hot water tank temperature will this do it or do I require additional components View answer

Asked 5 ´years ago | Z-Wave Secure Pipe Tank Digital Temperature Sensor - 4m Wire

Question 8

is it compatible with HS3 View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - Three Clamps (60A)

Question 9

How "tall" is the connector? Will it fit on top of this Raspberry Pi 4 case? https://images-na.ssl-images-amazon.com/images/I/71SXo28eeHL._SL1500_.jpg Thank you. View answers

Asked 5 ´years ago | Z-Wave.me RaZberry 2 PI GPIO Daughter Card - Gen5 - New

Question 10

you said: Popp Mains Adapter can be used to power up the Z-Wave Popp Smoke Detector with mains supply. It eliminates the need to insert batteries in your smoke detector. after we tried to install it without battery it doesn't work then we contacted aeotec support they said: The smoke detector only works with the battery inserted. The smoke detector standard stipulates this. The 12 V supply serves to support the lifetime of the device by supplying the Z-Wave circuit board with external voltage. This doubles the lifetime of the 9V battery. could you explain please? Ahmad View answer

Asked 5 ´years ago | Z-Wave Popp Mains Adapter

Question 11

Will it work with Fibaro (Home Center 2)?

Asked 5 ´years ago | Z-Wave Plus Secure SES303 Temperature & Humidity Sensor Gen5

Question 12

What Bypass should be used in a 2-Wire installation? The manual says; "When installing the Mini Dimmer, with LED loads, in a 2-wired installation, if the load connected to the output starts flickering, we recommend you use a Bypass." I have installed it in to a 2-wire installation with an LED light and it is flickering. The Aeotech and Fibaro dimmers all say that only their own bypass modules are compatible, is this also the case with the Qubino dimmers? View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 13

Can you measure the energy through the contractor separately from the smart meter unit View answer

Asked 5 ´years ago | Qubino 32A Contactor for Smart Meter

Question 14

Hi does this support LED bulbs? View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 15

Does this come with a Zwave licence or is that an additional cost? View answers

Asked 5 ´years ago | Z-Wave.me RaZberry 2 PI GPIO Daughter Card - Gen5 - New

Question 16

Will this device work fully with Hc2? Thanks View answer

Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer

Question 17

Can multiple thermostats be associated to this device? ie. Can mulitple devices call for heat via this switch ? View answer

Asked 5 ´years ago | Z-Wave Plus Secure Boiler Receiver HRT Gen5

Question 18

Is the battery rechargeable or replaceable? View answers

Asked 5 ´years ago | Z-Wave Philio Multisensor - PIR / Light / Temp - Gen5

Question 19

Does this module work with wood venitian blinds? View answer

Asked 5 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 20

Which z wave stick / hub / device do you recommend for use with Secure Thermostat / Receiver and Homeseer? Please note I am a long time user of Homeseer (early 2000) upgrading from HS1,2 to HS3. For the last 15 years I have used a purpose designed multi (6) zone system controlled by Homeseer running Xap plugin to Phaedrus NETIOM to create heating scenes. I am now moving on to an existing single zone combi boiler dwelling. I have no desire or requirement to rejig the new system to a plumbed multi-zone effort. I see this combination as a first step to migrate to a zwave set up from my X10 devices, curing the heating issue in the process. View answer

Asked 5 ´years ago | Z-Wave Plus Secure Wall Thermostat & Receiver Set - Gen5

Question 21

Does this control both hot water and heating? View answers

Asked 5 ´years ago | Z-Wave Plus Secure Boiler Receiver HRT Gen5

Question 22

Why should i use this product? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Nano Dimmer Bypass

Question 23

On what Mhz does it works and does it work on a HC2 from Fibaro View answer

Asked 5 ´years ago | Yale Smart Living Z-Wave Module 2

Question 24

Can this be mounted outside? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 25

Please advise the lead time for these modules. We need to procure 5 of them as soon as available. Regards, Warwick

Asked 5 ´years ago | Z-Wave.me RaZberry 2 PI GPIO Daughter Card - Gen5 - New

Question 26

I've tried to standardise with Fibaro kit but their Dimmer 2 doesn't appear to offer 0-10V output like this Qubino Flush Dimmer. Is that right? View answer

Asked 5 ´years ago | Z-Wave Qubino Flush Dimmer 0-10V Plus

Question 27

Hello, I was wondering whether you have this item suitable for an american-style box, at the size of 120mm wide, instead of 86mm? Thanks, Gal.

Asked 5 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Two Load - UK

Question 28

Managed to put in a workaround but I found with a original style lightbulb it would cut out when I turn the brightness above 60% and then start flashing red. I've updated the config so that max power is 60% as this is just the porch light and I don't really need it that bright in there. But I'm concerned what happens if I purchase more.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 29

I ordered this product before 3 days. Can you tell when the item will be in stock? Thank you.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 30

I have purchased this and it works fine, but I can't find a way to mount it nicely. UK backboxes and the extension plates for them have recessed mounting tabs. The switch can xxxx on to these with no problem, but it is recessed too far for the front cover to be able to clip onto the main switch housing. Please advise.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 31

Hi, I'm using Domoticz running on a RPi, does this classify as a 'security Enabled Z-Wave Plus Controller' as specified as a requiremjent to fully utilise the Remotec ZXT-600 Z-Wave+ to IR Extender for AC ? Thanks Steve View answer

Asked 5 ´years ago | Z-Wave Remotec ZXT-600 Z-Wave+ to IR Extender for AC

Question 32

Will the Z-Wave Qubino Flush Dimmer 0-10V Plus work with Samsung smartthings to control my Ecopac Constant Voltage 0/1-10V Dimmable LED Driver ELED-200-24V 200W 24V

Asked 5 ´years ago | Z-Wave Qubino Flush Dimmer 0-10V Plus

Question 33

I wish to use this to wirelessly (zwave) control my Danfoss thermostats (also Zwave). Can you confirm that this devise is able to do so? And, I wonder if the fan-controller can be used to automatically turn on a fan for heat-moving near the fireplace? Say, if it is 23 degree it should automatically turn on the vent. But if it is too noisy or so, I can turn down the speed? Its hard to find the exact details on this product and MCO does not reply on their website... Thanks! View answer

Asked 5 ´years ago | Z-Wave Plus MCO Home Fan Coil Thermostat - 4 Pipe

Question 34

Can this product be used outdoors? View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 35

Can the unit be run from a USB / mains power supply? I don't trust the battery life claims from manufacturers. View answer

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 36

Is this Trisensor replacing the Aeotec Multisensor 6, which has 6 different sensors?

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 37

Do these use the same motion sensor as Aeotec's Multisensor with motion, UV, humidity, vibration, temperature and lux? I'm hoping they don't as the motion sensor in the Aeotec 6-way multisensor is very poor, I have about 5-6 of them and even on the highest setting they often don't detect me even if I walk right up to them and jump around.

Asked 5 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 38

When was this published?

Asked 5 ´years ago | Z-Wave Essentials Book

Question 39

I currently have a single piece door handle and lock cover on a uPVC door. 1. It looks as though this device only covers the lock - is this assumption right? 2. Does it then need mounting to the door with screws? I'm just a little concerned about more holes in the door... Anyone actually fitted one? A few practical comments would be invaluable. Thanks View answer

Asked 5 ´years ago | Z-Wave and Bluetooth Poly-Control Danalock V3

Question 40

What's the difference between roller shutter 2 & 3? Are there any new features to note?

Asked 5 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 41

Im attempting to use this with HomeSeer, has anyone else managed to use a backup & restore function with the same set up ?

Asked 5 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 42

How does this differ from Roller Shutter 2? View answer

Asked 5 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 43

I've currently got an AEON S2 installed in my Domoticz environment with a fairly large network of devices. Some of them are in pretty inaccessible spaces. I'm now considering changing the controller but I need to be sure that I can transfer the configuration without re-including the devices. Gareth

Asked 5 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 44

The manual shows this can handle 200A ? I need a single phase meter to cover 100A - will this one work? if not which one will? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 45

Hi, I have recently installed a set of electric gates with intercom. Can I simply wire this into the existing system such that it will behave as before with the added functionality of control via app? I would be using with SmartThings - should I have any concerns about my gates accidentally/unexpectedly opening? Thanks, Declan.

Asked 6 ´years ago | Z-Wave Popp Electronic Door Opener Controlmodule

Question 46

Can the temperature sensitivity be increased using parameters to change the bit length of the temperature sensor?

Asked 6 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 47

How do I programme the Aeon Labs Clamp meter to record import & export units on Vera Plus?

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 48

what frequency this item is US/EU? View answer

Asked 6 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 49

Is there a reason why this has to be hardwired into the main circuit box panel rather than a plug? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 50

I have a British Gas ES1 (Drayton RTS5) thermostat with up to an hour delay on switch-on that requires a press on the ‘Save’ button to bypass the delay. I now have a Secure SRT321 thermostat with a SSR302 boiler control. Although I have turned the ES1 up to the max, I am now subjected to the delay of the ES1 everytime that the SRT321 switches on the heating throughout the day. I am trying to avoid finding the junction box to bridge out the ES1, so would like to reconfigure/bridge the wiring behind the ES1 to cut-out the delay. Has anybody tried this before, or knows how to do it?

Asked 6 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display

Home Assistant Compatible Q&A

Activity timeframe

Browse by Category

Browse by Category

Browse by Topic

Tools