Asked 4 ´years ago | Fibaro Home Center 3
Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer
Multiple questions --> What is the difference between the bi-stable and the contactor switch ? I need to switch a load of ~ 4k W (electrical water heater) which uses a double switch (live+neutral), which one suits better ? Do u have any feedback from Vera users that have managed to add them in their network (smart meter, contactor, bi-stable) ? View answer
Asked 8 ´years ago | Qubino 32A Bistable Switch for Smart Meter
Sensor 6 has several flaws. Reset button link via a piece of dodgy plastic, poor light level reading, poor UV reading.Apart from these, it was very good. Have they been addressed in Sensor 7? E.G. What range is read for the light level?Can I trust the reset mechanism? Can I assume it will work well with RaZberry? View answer
Asked 3 ´years ago | Z-Wave Plus Aeotec MultiSensor 7
The marketing and product box for this item promotes that you can plug it in and power it from a nearby socket. They show this in the manual for the US 110v version , but for the UK/EU 230v version it suggests it has to be hard wired into the main consumer unit ?As I have a socket right next to the consumer unit? Please could someone explain why I can’t connect the power cable to a UK plug and power it, rather than pay for an electrician to hardwire it? View answer
Asked 3 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)
We are rewiring the house and as part of this will have a neutral at each switch. Two questions I have are 1) for loads less than 50W is a bypass still required even in a 3 wire setup? 2) is there a cheaper alternative to the fibaro which still offers smooth LED dimming? Thanks. View answer
Asked 4 ´years ago | Z-Wave Fibaro Universal Dimmer 2
Which z wave stick / hub / device do you recommend for use with Secure Thermostat / Receiver and Homeseer? Please note I am a long time user of Homeseer (early 2000) upgrading from HS1,2 to HS3. For the last 15 years I have used a purpose designed multi (6) zone system controlled by Homeseer running Xap plugin to Phaedrus NETIOM to create heating scenes. I am now moving on to an existing single zone combi boiler dwelling. I have no desire or requirement to rejig the new system to a plumbed multi-zone effort. I see this combination as a first step to migrate to a zwave set up from my X10 devices, curing the heating issue in the process. View answer
Asked 5 ´years ago | Z-Wave Plus Secure Wall Thermostat & Receiver Set - Gen5
Asked 3 ´years ago | Z-Wave Plus V2 Heltun Touch Panel Switch - Four Buttons - White
Will this device work fully with Hc2? Thanks View answer
Asked 5 ´years ago | Z-Wave Plus Qubino Mini Dimmer
Will this work with Samsung Smartthings ? View answer
Asked 5 ´years ago | All > Z-Wave Fortrezz Outdoor Siren & Strobe Alarm
you said: Popp Mains Adapter can be used to power up the Z-Wave Popp Smoke Detector with mains supply. It eliminates the need to insert batteries in your smoke detector. after we tried to install it without battery it doesn't work then we contacted aeotec support they said: The smoke detector only works with the battery inserted. The smoke detector standard stipulates this. The 12 V supply serves to support the lifetime of the device by supplying the Z-Wave circuit board with external voltage. This doubles the lifetime of the 9V battery. could you explain please? Ahmad View answer
Asked 5 ´years ago | Z-Wave Popp Mains Adapter
is it good for outdoor use? View answer
Asked 2 ´years ago | Z-Wave Plus Sensative Strips Guard 700
Asked 2 ´years ago | Hubitat Elevation Model C-7 Hub
Does this have a uk plug ? View answer
Asked 2 ´years ago | Shelly Gas LPG
Will it work wit fibaro HC Lite? View answer
Asked 8 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch
