Question 1

Asked 5 ´years ago | Z-Wave Plus Aeotec Siren 6

Question 2

Hello, I was wondering whether you have this item suitable for an american-style box, at the size of 120mm wide, instead of 86mm? Thanks, Gal.

Asked 5 ´years ago | SmartThings Compatible > Z-Wave Plus MCO Touch Panel Switch - Two Load - UK

Question 3

Managed to put in a workaround but I found with a original style lightbulb it would cut out when I turn the brightness above 60% and then start flashing red. I've updated the config so that max power is 60% as this is just the porch light and I don't really need it that bright in there. But I'm concerned what happens if I purchase more.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 4

I ordered this product before 3 days. Can you tell when the item will be in stock? Thank you.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 5

I bought two of these to replace the previous generation ones. however, I'm unable to control these lights remotely on my Vera unit from other devices. Aeotec 4 button remote. I've seen other people who can't now remotely control these. Any ideas?

Asked 5 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 6

I have a fibaro lite home center - with sensor strips on windows and doors. Is this compatible? View answer

Asked 5 ´years ago | Z-Wave Popp Solar Outdoor Siren 2

Question 7

I have purchased this and it works fine, but I can't find a way to mount it nicely. UK backboxes and the extension plates for them have recessed mounting tabs. The switch can xxxx on to these with no problem, but it is recessed too far for the front cover to be able to clip onto the main switch housing. Please advise.

Asked 5 ´years ago | Z-Wave Fibaro Walli Dimmer

Question 8

what kind of range should I expect for this? I have a lot of walls between where my vera is and where my 433 device is... View answer

Asked 5 ´years ago | RFXtrx433XL USB 433.92 MHz transceiver with antenna (NEW model)

Question 9

I will be building a new house starting in a few months time and I want to implant temperature sensors in the concrete slab. I have 2 questions; firstly in the manual it says this can be burried concrete with the right protection, what would that protection be please?? Secondly, what would you recommend for protecting the string of temp tensors so they can be safely buried in the concrete and what cable would you connect them with ?? Thanks Chris

Asked 5 ´years ago | Z-Wave Fibaro Smart Implant

Question 10

Hi, I'm using Domoticz running on a RPi, does this classify as a 'security Enabled Z-Wave Plus Controller' as specified as a requiremjent to fully utilise the Remotec ZXT-600 Z-Wave+ to IR Extender for AC ? Thanks Steve View answer

Asked 5 ´years ago | Z-Wave Remotec ZXT-600 Z-Wave+ to IR Extender for AC

Question 11

Does this support pulse counting at hardware level ? I'm looking for something to interface to water flow meters with a pulsed output. It would obviously need to store number of pulses received over a certain time period.

Asked 5 ´years ago | Z-Wave Fibaro Smart Implant

Question 12

Will this work with Samsung Smartthings ? View answer

Asked 5 ´years ago | All > Z-Wave Fortrezz Outdoor Siren & Strobe Alarm

Question 13

Will the Z-Wave Qubino Flush Dimmer 0-10V Plus work with Samsung smartthings to control my Ecopac Constant Voltage 0/1-10V Dimmable LED Driver ELED-200-24V 200W 24V

Asked 5 ´years ago | SmartThings Compatible > Z-Wave Qubino Flush Dimmer 0-10V Plus

Question 14

When will this product be in stock? View answer

Asked 5 ´years ago | Athom Homey Pro

Question 15

This appears to be a re-incarnation of the Fibaro Universal Binary Sensor which will not now recognise DS18B20 inputs although it used to do so. Is this unit any the more reliable?

Asked 6 ´years ago | Z-Wave Fibaro Smart Implant

Question 16

I wish to use this to wirelessly (zwave) control my Danfoss thermostats (also Zwave). Can you confirm that this devise is able to do so? And, I wonder if the fan-controller can be used to automatically turn on a fan for heat-moving near the fireplace? Say, if it is 23 degree it should automatically turn on the vent. But if it is too noisy or so, I can turn down the speed? Its hard to find the exact details on this product and MCO does not reply on their website... Thanks! View answer

Asked 6 ´years ago | Z-Wave Plus MCO Home Fan Coil Thermostat - 4 Pipe

Question 17

Hi, When will the Z-Wave Fibaro Double Switch 2 be available in stock? I have been waiting for the appearance of this device around a week( View answer

Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2

Question 18

Hi. Can I use 3 x 7W led bulbs and 1 x 3W led bulb on the same circuit? Or do all the bulbs need to be the same wattage? Thanks View answer

Asked 6 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 19

Good afternoon- can you confirm that this will only work with Popp ? and is NOT compatible with any Z-Wave hub devices ie Fibaro ? Best regards Chris

Asked 6 ´years ago | Popp 433 Bridge - Black

Question 20

Can this product be used outdoors? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 21

Can the unit be run from a USB / mains power supply? I don't trust the battery life claims from manufacturers. View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 22

Is this Trisensor replacing the Aeotec Multisensor 6, which has 6 different sensors?

Asked 6 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 23

Do these use the same motion sensor as Aeotec's Multisensor with motion, UV, humidity, vibration, temperature and lux? I'm hoping they don't as the motion sensor in the Aeotec 6-way multisensor is very poor, I have about 5-6 of them and even on the highest setting they often don't detect me even if I walk right up to them and jump around.

Asked 6 ´years ago | Z-Wave Plus Aeotec Trisensor

Question 24

When was this published?

Asked 6 ´years ago | Z-Wave Essentials Book

Question 25

I am using the Fibaro Dimmer 2 to control the main lights in my lounge on S1, and to control the lamps by association in Group 5 which are connected to wall dimmers using S2. I have managed to get it all working, but I would like to connect more than one lamp. I have tried to add a second association but it never seems to stick. I have attempted this with OpenHAB, my main server, and with Domoticz control centre. Can you tell me whether this is possible? From the limited documentation I can find, and my experience with associating other devices, I believe it should be.

Asked 6 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 26

I am looking for a capacitive mono-stable wall switch to be used with a z-wave dimmer module. I'm struggling to find ones which will work as desired as most will not register a long press/hold – instead, they always accept touch as a momentary on/off. What I would like is for it to mimic a mono-stable switch (bell-push) i.e. touch once for on/off and hold for dim up/down, which I know can be set by the Fibaro parameters – but I can't find a capacitive plate wall plate that does this. Note, ideally I'm looking a double switch.

Asked 6 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 27

Hi! This dimmer operate in Europe frequency range? Thanks View answer

Asked 6 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 28

Hi, To control the lights via z-wave do I have to keep this switch always "on"? Or i can control via z-wave regardless of the status of the touch pannel? Thanks, Z View answer

Asked 6 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 29

I currently have a single piece door handle and lock cover on a uPVC door. 1. It looks as though this device only covers the lock - is this assumption right? 2. Does it then need mounting to the door with screws? I'm just a little concerned about more holes in the door... Anyone actually fitted one? A few practical comments would be invaluable. Thanks View answer

Asked 6 ´years ago | Z-Wave and Bluetooth Poly-Control Danalock V3

Question 30

What's the difference between roller shutter 2 & 3? Are there any new features to note?

Asked 6 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 31

So I have this bulb now, it's connected to my vera plus, I can get it to dim and switch on/off. How to i change the color with in vera. Thanks

Asked 6 ´years ago | Z-Wave Plus Aeotec LED Bulb 6 Multi-White (E27)

Question 32

Im attempting to use this with HomeSeer, has anyone else managed to use a backup & restore function with the same set up ?

Asked 6 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 33

How does this differ from Roller Shutter 2? View answer

Asked 6 ´years ago | Z-Wave Fibaro Roller Shutter 3

Question 34

I've currently got an AEON S2 installed in my Domoticz environment with a fairly large network of devices. Some of them are in pretty inaccessible spaces. I'm now considering changing the controller but I need to be sure that I can transfer the configuration without re-including the devices. Gareth

Asked 6 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 35

Can you use this to update Aeotec firmware using their Window tools?

Asked 6 ´years ago | Z-Wave.Me USB Stick

Question 36

The manual shows this can handle 200A ? I need a single phase meter to cover 100A - will this one work? if not which one will? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 37

Hi, I have recently installed a set of electric gates with intercom. Can I simply wire this into the existing system such that it will behave as before with the added functionality of control via app? I would be using with SmartThings - should I have any concerns about my gates accidentally/unexpectedly opening? Thanks, Declan.

Asked 6 ´years ago | Z-Wave Popp Electronic Door Opener Controlmodule

Question 38

Hello, you did not mention the frequency of z-wave signal? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Heavy Duty Outdoor Switch

Question 39

Can the temperature sensitivity be increased using parameters to change the bit length of the temperature sensor?

Asked 6 ´years ago | Z-Wave Plus Aeotec MultiSensor 6

Question 40

How do I programme the Aeon Labs Clamp meter to record import & export units on Vera Plus?

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 41

what frequency this item is US/EU? View answer

Asked 6 ´years ago | Aeotec Z-Stick Gen5 USB Controller (NEW Raspberry Pi 4 compatible)

Question 42

Is there a reason why this has to be hardwired into the main circuit box panel rather than a plug? View answer

Asked 6 ´years ago | Z-Wave Plus Aeotec Clamp Power Meter - One Clamp (60A)

Question 43

Hi, I've recently purchased one of these devices and installed it on my veraplus. Its created the 'Double Switch 2', Q1 Load, and Q2 Load. On the double switch device, its got the status: Failed at: Setting special association. The 2 load switches appear to work ok. Any ideas how to resolve? Thanks View answer

Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2

Question 44

Hi. How do you set the parameters for the dimmer 2 with tellstick sent Fibaro Dimmer 2 Parameter Setting: The following parameters need to be set: 20 - 1 - enables the dimmer to work with a toggle switch (default is 0 for a momentary switch) 26 - 1 - enables the dimmers S2 switch to also control the dimmer (default 0) Thanks

Asked 6 ´years ago | Z-Wave Fibaro Universal Dimmer 2

Question 45

Does this unit works with HC2 (Fibaro) or is there any ready made easy integration possible? View answer

Asked 6 ´years ago | RFXtrx433XL USB 433.92 MHz transceiver with antenna (NEW model)

Question 46

Why is this only compatible to the POPP Hub? I thought all Z-Wave devices were compatible. View answer

Asked 6 ´years ago | Popp 433 Bridge - Black

Question 47

Does this switch supports dimmable LED lights? View answer

Asked 6 ´years ago | Z-Wave Plus MCO Touch Panel Switch - Four Load - UK

Question 48

I have a British Gas ES1 (Drayton RTS5) thermostat with up to an hour delay on switch-on that requires a press on the ‘Save’ button to bypass the delay. I now have a Secure SRT321 thermostat with a SSR302 boiler control. Although I have turned the ES1 up to the max, I am now subjected to the delay of the ES1 everytime that the SRT321 switches on the heating throughout the day. I am trying to avoid finding the junction box to bridge out the ES1, so would like to reconfigure/bridge the wiring behind the ES1 to cut-out the delay. Has anybody tried this before, or knows how to do it?

Asked 6 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display

Question 49

Would this work locally "out of the box" without connecting to a central z-wave controller? I understand remote commands require a controller but would a hardwired momentary switch be able to turn on the load immediately after wiring as well? View answer

Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2

Question 50

Just read the English installation instructions for the Fibaro FGS 223. They state "The device is designed for installation in a wall switch box of depth not less than 600mm." I'm not sure you can get a back box of that depth in the UK. Does this mean we can't use the device in a standard UK box? View answer

Asked 6 ´years ago | Z-Wave Fibaro Double Switch 2

Browse by Topic

Tools