Can this be used with the 2 channel boiler receiver? If so, how does it manage the hot water channel? I have a Razberry but wanted this to manage in the case of its failure (and because I understand it will manage the boiler better?) View answers
Asked 7 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
Why does the Aeotec Multi 6 report a 23 lux when my Philips Hue sensor reports 14606 lux in virtually the same position. I've tried it with 3 Aeotec Multi 6s now with the same sort of difference, I'm concerned because I want to use to switch on lighting when required? They even report 0 lux when there is enough light to read a book! View answers
Asked 4 ´years ago | Z-Wave Plus Aeotec MultiSensor 6
What connectors do I need to order to extend this cable? I can get them from Farnell or RS if I know what are used. I'm assuming that this is a 1-wire sensor as it has three wires, pwr, gnd and the 1-wire bus, and that means that it can be extended to quite a few metres and I need to pick up the outside temperature... View answers
Asked 7 ´years ago | Qubino Temperature Sensor
Hi all, I have installed a couple of these (fgs223) on a 2 way switch. One is an on off switch and the other is a dimmer. I've put the switches behind the on off switch. That bit works well but now the separate dimmer won't dim it only switches on and off. Any suggestions? View answers
Asked 7 ´years ago | Z-Wave Fibaro Double Switch 2
Has this been tested for Vera ui7 yet? View answers
Asked 8 ´years ago | Z-Wave Remotec Scene Master
Does this work with homeseer hs3? View answers
Asked 8 ´years ago | Z-Wave Fibaro Universal Dimmer 2
Does this need ventilation? I was planning on using these in the loft for the upstairs lighting and putting them in PVC boxes along with any connectors etc. This is to keep things neat and safe but wondered if I need to drill holes in the boxes for ventilation? View answers
Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2
I have a fused Switch controlling a fan and want to use this controller to operate the fan remotely as well as enabling the fused switch to continue controlling the fan at the wall, is there a wiring diagram showing how to achieve this? View answers
Asked 6 ´years ago | Z-Wave Plus Aeotec Nano Switch On/Off Controller
I bought this motion sensor and tried without success to include to my new smartthings hub v2 (UK version). Smartthings support advised me to confirm that the motion sensor is also a UK version (not a US one), as apparently the frequencies are different... Can you please confirm that this sensor works with the UK version of smartthings hub? View answers
Asked 6 ´years ago | Z-Wave Fibaro Multi Sensor
How many 240V GU10 Led Bulbs (Dimmable ones) can the FD2 support? I have 3 light fittings for outside my house that house 2 GU10 240 Bulbs or GU10 240V Dimmable Bulbs. I am going to use the LED Dimmable bulbs which on the box say "Use only 7 watts per bulb". So a total of 6 bulbs in 3 light housings. I'm going to wire them back to a junction box in parellel (not serial) and into then into the FB2 but was worried that 6 bulbs of this type (or even 10) would fry it? I have the original Fibaro Bypass Module also (FGB001) which I bought a few years ago but never used, could I use this if I need it? The LED 240v GU10 bulbs are "dimmable" Thanks! Andy View answers
Asked 7 ´years ago | Z-Wave Fibaro Universal Dimmer 2
How do you use this module? View answers
Asked 8 ´years ago | Qubino Temperature Sensor
Hi. Has anyone had a good experience with these? The concept is great, but not if it doesn't work! Is it the firmware that is unstable, or the controller software? Have the Vesternet staff had any experience with them? Also, are they always listening, or do they have a wake up period? Thanks, Ed View answers
Asked 6 ´years ago | Z-Wave Fibaro Heat Controller
Does this module work with Fibaro? View answers
Asked 6 ´years ago | Yale Smart Living Z-Wave Module 2
Can this unit be used to trigger events in a controller (in my case the Homeseer Hometroller Zee S2) rather than being paired with a boiler receiver? I have two electric radiators in a room, and want to turn them on and off based on the thermostat reading. So I would create the various events to change the set point in the Homeseer, but also want the thermostat to trigger the events which turn the radiators on and off. Would that work, or should I be looking at something else? View answers
Asked 8 ´years ago | Z-Wave Plus Secure Wall Thermostat with LCD display
Can this device with Fibaro Home Centre 2? View answers
Asked 8 ´years ago | Z-Wave Qubino Flush Shutter DC
